How To Measure For Wood and Faux Wood Blinds

What you will need:

• A metal tape measure
• Pen/pencil and piece of paper/notepad

When ordering multiple blinds at very similar widths a difference of even 1millimetre can mean a change to the number of ladder cords/tapes used as well as the position of these. Similarly, a slight difference in drop can mean additional slats covering the drop of the blind. This is important to bear in mind where blinds are to be installed in close proximity, and you want a uniform look. If your installation is like this and you need help email us for further measuring advice.

You will usually have at least 1-2 slats sitting on the base rail of the blind when the blinds are fully lowered. These slats keep the base rail flush to the windowsill when you angle the slats and ensure the full height of the window is covered.

Please note we do not recommend installing our real wood venetian blinds in bathrooms, or kitchens. We do not recommend installing our faux wood or real wood venetian blinds in conservatories. This is due to the conditions in those areas being unsuitable for a long life of these products. Email us for alternative production recommendations.

How To Take a Recess Size Measurement

Measuring Inside The Recess

If you order you Wood or Faux Wood blinds as Recess size we’re going to make the width of your blind approximately 1cm to 1.5cm narrower than the width you give. This is so the blind fits nicely inside your recess and the slats do not scrape against the recess walls. We leave the height as it is so the base rails sits on the window sill. It’s important that you do not make any deductions yourself.

When you order your Real Wood or Faux Wood Venetian as Recess Size the pelmet will arrive at the same width as the blind and will be square cut at each end. There will be no end returns supplied for the headrail as the recess walls will be covering each end of the headrail.

Follow the instructions below on how to measure your window recess;

1. Use a metal tape and measure in centimetres to the nearest 0.1cm (1 millimetre).
2. Measure the width of the recess from wall to wall in three places as shown in the diagram above. Use the shortest measurement of the three if they vary.
3. Measure the drop by taking the measurement from the top of the recess to the windowsill in three places as shown in above. Use the shortest measurement of the three if they vary.
4. Write down your width and height measurement as you go to the nearest 0.1cm (1 millimetre). Clearly note which is the width and which is the height. We recommend you write down the width first then the height as when you order your blinds you will always be required to enter the width first and then the height so this will help prevent any errors when you come to order.
5. If there are any obstructions within the window recess, like projecting window handles or Dado Rails and you are confused about what to do just email us for advice.
6. Use these measurements to order and select the Recess size option.

Child Safety

Due to Child Safety legislation, controls on all blinds must be at least 150cm from the floor so they are securely out of reach of young children. To avoid controls which are too short for you to reach, there is a section when ordering called the Installation Measurement. The installation measurement is the measurement from where the very top of the blind will be installed down to the floor. If you supply the installation measurement when ordering we will make sure your cords/chains are long enough for you to reach but still safely out of the reach of young children. We also recommend you still use the child safety devises we supply to secure the chains under tension or to wrap excess cord around too as an extra precaution.

How To Take an Exact Size Measurement

Measuring Outside The Recess

If you order as Exact size your blind will be made to the sizes you give to us. We do not make deductions. (We do work to an industry standard manufacturer’s tolerance of plus/minus 5mm). 

If you order a faux wood / real wood venetian as Exact size your width will be made to the size you specify. (We do work to an industry standard manufacturer’s tolerance of plus/minus 5mm). The height of the blind can be slightly longer as we need to ensure we add enough slats to cover the entire height (i.e. we have to add a whole 50mm slat even if only 2mm at the bottom of the blind still needs to be covered making the blind slightly longer).

For Exact sized faux wood/ real wood venetians the pelmets will be mitred at each end. End returns will be supplied to cover each end of the headrail.

1. Use a metal tape and measure in centimetres to the nearest 0.1cm (1 millimetre).
2. Measure the exact width of where you would like you blind to cover. Allow a similar amount of overlap on each side if fitting outside of a recess, as shown above.
3. Measure the exact height of where you would like the top of the blind to be installed down to where you want the blind to end. If you are installing outside of a window recess allow a similar amount of overlap at the top and bottom as shown above. Never try and fit too close to the top line of a window recess or window frame, as the plaster may crumble. We would recommend allowing at least 5cm above the top of the window to ensure secure fixing.
4. Write down your width and height measurement as you go to the nearest 0.1cm (1 millimetre). Clearly note which is width and which is the height. We recommend you write down the width first then the height as when you order your blinds you will always be required to enter the width first and then the height so this will help prevent any errors when you come to order.
5. Use these measurements to order and select the Exact size option.

Child Safety

Due to Child Safety legislation, controls on all blinds must be at least 150cm from the floor so they are securely out of reach of young children. To avoid controls which are too short for you to reach, there is a section when ordering called the Installation Measurement. The installation measurement is the measurement from where the very top of the blind will be installed down to the floor. If you supply the installation measurement when ordering we will make sure your cords/chains are long enough for you to reach but still safely out of the reach of young children. We also recommend you still use the child safety devises we supply to secure the chains under tension or to wrap excess cord around too as an extra precaution.