How To Measure For Z-Lite Roller

What you will need:

• A metal tape measure
• Pen/pencil
• Paper/notepad

How To Take a Recess Size Measurement

Measuring Inside The Recess

If you order your Z-Lite blinds as recess size we are going to make the width of your blind at the exact width you supply. We reduce the overall blind height by approximately 1.0cm to allow for slight variation in the sill height. This blind type is designed to NOT touch your window sill. You do not make any deductions yourself.

Follow the instructions below on how to measure your window recess;

1. Use a metal tape and measure in centimetres to the nearest 0.1cm (1 millimetre).
2. Measure the width of the recess from wall to wall in three places as shown in the diagram above. Use the shortest measurement of the three if they vary.
3. Measure the drop by taking the measurement from the top of the recess to the windowsill in three places as shown in above. Use the shortest measurement of the three if they vary.
4. Write down your width and height measurement as you go to the nearest 0.1cm (1 millimetre). Clearly note which is width and which is the height. We recommend you write down the width first then the height as when you order your blinds you will always be required to enter the width first and then the height so this will help prevent any errors when you come to order.
5. If there are any obstructions within the window recess, like projecting window handles or Dado Rails and you are confused about what to do just email us for advice.
6. Use these measurements to order and select the Recess size option.

Child Safety

Due to Child Safety legislation, controls on all blinds must be at least 150cm from the floor so they are securely out of reach of young children. To avoid controls which are too short for you to reach, there is a section when ordering called the Installation Measurement. The installation measurement is the measurement from where the very top of the blind will be installed down to the floor. If you supply the installation measurement when ordering we will make sure your control chain is long enough for you to reach but still safely out of the reach of young children. We also recommend you still use the child safety device we supply to secure the chain under tension as an extra precaution.   

How To Take an Exact Size Measurement

Measuring Outside The Recess

If you order your Z-Lite as Exact size your blind will be made to the sizes you give to us. We do not make any deductions. (We do work to an industry standard manufacturer’s tolerance of plus/minus 5mm).

Follow the instructions below on how to measure for your exact sized Z-Lite blind;

1. Use a metal tape and measure in centimetres to the nearest 0.1cm (1 millimetre).
2. Measure the exact width of where you would like you blind to cover. Allow a similar amount of overlap on each side if fitting outside of a recess, as shown above.
3. Measure the exact height of where you would like the top of the blind to be installed down to where you want the blind to end. If you are installing outside of a window recess allow a similar amount of overlap at the top and bottom as shown above. Never try and fit too close to the top line of a window recess or window frame, as the plaster may crumble. We would recommend allowing at least 5cm above the top of the window to ensure secure fixing.
4. Write down your width and height measurement as you go to the nearest 0.1cm (1 millimetre). Clearly note which is width and which is the height. We recommend you write down the width first then the height as when you order your blinds you will always be required to enter the width first and then the height so this will help prevent any errors when you come to order.
5. Use these measurements to order and select the Exact size option.

Child Safety

Due to Child Safety legislation, controls on all blinds must be at least 150cm from the floor so they are securely out of reach of young children. To avoid controls which are too short for you to reach, there is a section when ordering called the Installation Measurement. The installation measurement is the measurement from where the very top of the blind will be installed down to the floor. If you supply the installation measurement when ordering we will make sure your control chain is long enough for you to reach but still safely out of the reach of young children. We also recommend you still use the child safety device we supply to secure the chain under tension as an extra precaution.